How much does garage door repair cost?
Most garage door repairs cost $150 to $350, according to HomeGuide’s 2026 guide. Angi’s 2026 guide sets the national average at $265, with typical jobs between $155 and $379, and reports repairs as low as $80 and above $700.
National cost guides place a typical single-part garage door repair between $150 and $379. Each guide prices a slightly different job, so the table shows every range as published instead of blending them into one number. The failed part sets the price: a photo-eye realignment sits at the low end, and a replaced section sits at the high end.
| Publisher | Year | Low | High | What the range covers |
|---|---|---|---|---|
| HomeGuide | 2026 | $150 | $350 | Most repairs, parts and labor; minimum service fees apply |
| Angi | 2026 | $155 | $379 | Typical repair; $265 average; labor $150–$450 per job |
| Angi (roller guide) | 2026 | $150 | $250 | Full roller replacement, parts and labor; $200 average |
Need the price for your own door? Call (833) 752-1196. The technician names the failed part and gives you the price before any work starts, with no trip fee anywhere in our North Carolina service area.
How much does it cost to fix a garage door, part by part?
A photo-eye sensor costs $125 to $300 to fix, a track $125 to $300 and a lift cable $150 to $350, according to HomeGuide’s 2026 guide. Angi’s 2026 guides put rollers at $150 to $250 and a single panel at $250 to $1,000.
The table sets 3 national guides beside Angi’s Raleigh page, the only North Carolina source with part-level figures. A blank in one guide is written as “not listed”; no range is merged or guessed.
| Part | HomeGuide 2026 | Angi 2026 | This Old House 2026 | Angi, Raleigh NC 2026 |
|---|---|---|---|---|
| Lift cables | $150–$350 | $100–$400 | $170–$320 | Not listed |
| Rollers (full set) | Not listed | $150–$250 (roller guide); $110–$230 (repair guide) | Not listed | Not listed |
| Track | $125–$300 to replace; $200–$350 off-track realignment | $75–$125 to straighten a bent track | Not listed | $115–$275 |
| Panel (one section) | $300–$900 | $250–$1,000 | Not listed | $230–$470 |
| Photo-eye sensor | $125–$300 | $150–$250 | Not listed | $75–$135 realignment |
| Opener repair | $100–$200 | $100–$500 | Not listed | $95–$220 motor repair |
| Springs | $150–$350 | $180–$350 | On the spring cost page | $140–$320 |
Lift cables
Lift cables are 1/8 in galvanized steel cables that run from each bottom corner of the door to the cable drums on the spring shaft. A snapped or frayed cable leaves the door crooked, or stuck part-way open.
Rollers
Rollers are the nylon or steel wheels on stems that run in the tracks. A standard door runs on 10 to 12 rollers, and worn steel rollers are the usual source of grinding noise.
Tracks
The vertical and horizontal tracks guide the rollers from the floor to the ceiling. A bent track or a door off its track stops the door, and the price rises when the door has to be re-hung on its cables.
Panels
A sectional door is built from 4 or 5 horizontal sections, or panels. One creased or cracked section is replaced on its own when the maker still produces that model and color.
Photo-eye sensors
The photo-eyes are the pair of sensors mounted 6 in or less above the floor that reverse a closing door when the beam is broken. Most faults are misalignment, a dirty lens or a damaged wire.
Opener repairs
Stripped drive gears, failed start capacitors and failed logic boards are the common opener repairs. The spread between publishers is widest here: $100 to $200 at HomeGuide against $100 to $500 at Angi.
How much does garage door cable replacement cost?
Garage door cable replacement costs $150 to $350, according to HomeGuide’s 2026 guide. Angi’s 2026 guide reports $100 to $400 with labor, and This Old House’s 2026 guide $170 to $320. A broken spring often leaves the cables slack or frayed, so both appear on one bill.
Each lift cable winds onto a cable drum at one end of the spring shaft, and the springs’ stored force reaches the door only through those 2 cables. Technicians replace the cables as a pair, because both have run the same number of cycles. Near the coast, salt air corrodes cables and springs and shortens their life (DASMA TDS 190), so frayed strands appear sooner on coastal doors.
A door hanging on one cable stays closed and still until a technician arrives. The cable, the drum and the bottom bracket all hold spring tension, and none of them is loosened by hand.
How much does a garage door repairman charge to come out?
Angi’s 2026 guide reports national service-call fees of $50 to $75 and labor of $75 to $150 an hour. There is no trip fee anywhere in our North Carolina service area, and the technician gives you the price before any work starts.
A service visit runs in the same order on every door:
Diagnose
The technician runs the door and checks the springs, cables, rollers, track and opener to name the failed part.
Price
You get the price for that repair before any work starts.
Decide
The work starts only when you say yes.
Repair
The failed part is replaced, along with any worn part you approved at the price step.
Test
The door runs a full cycle and is checked for balance and auto-reverse.
Angi’s 2026 guide puts labor at $150 to $450 per job and parts at $5 to $200, so labor is the larger share of most single-part repairs.
What makes a garage door repair more expensive?
A repair costs more on a wood door, a door off its track, or a door whose panels are no longer made. Angi’s 2026 guide puts wood-door repairs at $200 to $300 against $100 to $200 for fiberglass; HomeGuide prices off-track realignment at $200 to $350.
Door material
Wood $200–$300, metal $150–$350 and fiberglass $100–$200 per repair (Angi 2026).
Door style
Sectional doors $150–$400 and one-piece tilt-up doors $400–$1,200 (Angi 2026).
Off-track door
Realignment $200–$350, against $125–$300 for a track replacement alone (HomeGuide 2026).
Discontinued panels
A section the maker no longer produces has no match, which turns a panel repair into a full door replacement on older doors (HomeGuide 2026).
Dent depth
Minor dents $100–$300 and moderate dents $250–$400 (HomeGuide 2026).
Two faults on one visit add up, and a broken spring with slack cables is a frequent pair. The technician lists every part in the price before any work starts, and the work starts only when you say yes.
Is garage door repair expensive compared with a new door?
No. A single repair averages $265 in Angi’s 2026 guide, while Angi prices a new door at $740 to $1,500. A single replacement panel at $250 to $1,000 approaches that figure, so two damaged panels on an older door favor replacement.
| Item | Published figure | Source |
|---|---|---|
| Average repair | $265 | Angi 2026 |
| One replacement panel | $250–$1,000 | Angi 2026 |
| New garage door | $740–$1,500 | Angi 2026 |
| Full garage door replacement | $970–$1,580 | This Old House 2026 |
A cable, roller, sensor or opener repair stays well under a new door’s price in every guide. The comparison turns only when sections are damaged: one panel on a sound door is a repair, and two or three panels on an older door approach the cost of the door itself.
Every range above is national; Angi also publishes repair price ranges for two North Carolina cities.
What does garage door repair cost in Charlotte and Raleigh?
Angi’s 2026 city pages put the average garage door repair at $294 in Charlotte and $251 in Raleigh. Charlotte jobs run $185 to $410 and Raleigh jobs $150 to $351. No statewide North Carolina average is published; the other figures are national.
| City | Average | Range | Page updated |
|---|---|---|---|
| Charlotte | $294 | $185–$410 | Aug 9, 2026 |
| Raleigh | $251 | $150–$351 | Aug 9, 2026 |
Angi’s Raleigh page also lists parts: a broken spring at $140 to $320, track repair at $115 to $275, panel replacement at $230 to $470, opener motor repair at $95 to $220 and sensor realignment at $75 to $135. A homeowner in Greensboro, Wilmington or Asheville compares the national ranges above, then gets the price for the actual door from the technician. To book a visit, request a repair price or call (833) 752-1196.
The fault-by-fault process is on the broken garage door repair page. Spring jobs are compared on the torsion spring price page. Technicians replace a dented section without replacing the door, and full-door figures sit with the new garage door cost ranges.